As a thank you for choosing Andersen, we are waving Basic Diagnostic & Dispatch Fees for a limited time only. *Excludes After Hours Calls
When temperatures in Plainfield drop below freezing and stay there for days at a time, a furnace that stops working becomes an emergency fast. Plainfield sits in Will County, where winter wind chills regularly push well below zero and homes built during the area’s rapid growth years now rely on furnace systems that have been running hard every winter since installation. A dependable team for furnace repair Plainfield, IL homeowners can count on makes the difference between a quick fix and a long cold night.
Andersen Plumbing, Heating and AC Repair has served Plainfield and the surrounding Fox Valley since 1985. Our licensed technicians diagnose and repair most furnace problems in a single visit, and we give you a clear price before we start any work.
A furnace rarely fails without warning. Here are the signs Plainfield homeowners should watch for before a minor issue turns into a system that will not run at all.
If you notice any of these, it is worth having a technician look at the system before the next cold snap arrives.
Plainfield grew quickly during the 1990s and 2000s, and a large share of the city’s furnaces are now old enough to be showing wear from repeated seasons of heavy winter use. Ignitors and flame sensors are common failure points in these systems, since they cycle on and off dozens of times a day throughout an Illinois winter and wear down faster than most homeowners expect.
The area’s temperature swings also put stress on heat exchangers. A cold snap that drops overnight lows well below zero followed by a milder afternoon forces metal components to expand and contract repeatedly, and over enough seasons that cycling can create small cracks that affect both safety and performance. Homes with older or leaky ductwork see an added complication, since heated air escaping into an attic or crawl space before reaching the living areas makes an aging furnace work even harder to keep up.
Blower motor wear and clogged filters round out the most frequent calls we get from Plainfield homeowners, particularly in homes where the filter has not been changed in several months heading into the coldest stretch of the year.
Our technicians handle the full range of furnace problems Plainfield homeowners run into during the heating season. We diagnose and repair ignitor and flame sensor failures, test and replace gas valves and pressure switches, and service blower motors and circuit boards when a system will not start or stops mid cycle.
We also inspect heat exchangers for cracks or corrosion, since this is both a performance issue and a safety concern that should never be ignored. Thermostat calibration, ductwork inspection, and filter assessment round out a complete diagnostic visit, so we can tell you exactly what is affecting your comfort and your energy bills rather than guessing at a single component.
We work on all major furnace brands and configurations, including standard forced air systems and high efficiency models. If a repair does not make sense for the age or condition of your system, we will tell you honestly and walk you through your options.
Linda called us on a January morning after her furnace had been running constantly but the house still felt cold. She lives in the Grande Park neighborhood on Plainfield’s east side, in a home built in the mid 2000s that still had its original furnace.
Our technician found that the flame sensor was coated with a thin layer of residue, which was causing the furnace to ignite briefly and then shut itself off as a safety measure before it could produce meaningful heat. This kind of short cycling is common in furnaces that have gone several seasons without a professional cleaning. The tech cleaned the sensor, tested the ignition sequence through several full cycles, and checked the heat exchanger and blower motor while he had the system open. Everything else was in good working order. Linda’s house was back to a steady, even temperature within the hour, and she scheduled an annual Check Up for the following fall so the same issue would not catch her off guard again.
Plainfield families have options when their furnace goes down, and here is what sets Andersen apart when the temperature drops.
Whatever your furnace needs, our team is ready to walk you through the honest answer and get your home warm again.
Age and repair history are the biggest factors. If your furnace is under 15 years old and this is its first significant issue, a repair usually makes sense. If it is older and has needed multiple repairs in recent winters, replacement may be the more practical choice. Our technicians will give you an honest assessment either way.
This is often caused by the system starting a heating cycle before the burners have fully ignited, or by a thermostat set to run the fan continuously. It can also point to an ignition delay or a dirty filter restricting airflow. A technician can pinpoint the exact cause quickly.
Once a year before the heating season begins is the general recommendation. A pre-season Check Up catches worn components like ignitors and flame sensors before they fail during the coldest part of winter. Our \$99 Membership Plan includes this visit on a regular schedule.
The plan includes an annual Check Up, priority scheduling when you need service, and ongoing savings on repairs throughout the year. For homeowners with older furnaces, the yearly visit often catches small issues before they turn into a mid-winter breakdown.
In most cases, yes. We work on all major brands and configurations, including standard forced air systems and high efficiency models. If a part is difficult to source for an older unit, we will tell you upfront and walk you through your options without any pressure.
